B-CUBE.RC - Build Your Drone From here- Build Your Drone From here!

B-CUBE 3-Axis Brushless Gimbal Camera Mount & 32bit Storm32 Controller Broad For Gopro3/Gopro4/SJ4000/Xiaomi FPV Camera Drone

$53.38 USD

~~$53.38 USD~~ $53.38 USD

Sale Sold out

Color Gimbal black Gimbal

Quantity

Please note that the camera is not included.

3-Axis Brushless Gimbal Camera Mount & 32bit Storm32 Controller Broad

3-Axis Brushless Gimbal Mount:

Description:
- Simple structure and light weight,CNC aluminum alloy structure
- Brushless motor direct drive
- With anti-vibration rubber balls,easy to adjust
- Compatible with Gopro 4 3,2,1
- With 3pcs 2804 160t motor
- With 32bit Storm32 firmware gimbal controller, sensor
- With motor protector which can help heat dissipation

Specification:
- Power supply: 9-15V(3-4S)
- Drive current: Max.1.5A
- Height: 11cm
- Color: White

2804 100KV Brushless Gimbal Motor

Model :2804 100KV
Weight:41.5g
Motor Diamension:34mm*hgt15mm
Stator Diameter:DIa 28mm*hgt 4mm
Copper Wire(OD):0.19mm
Configuration:12N14P
Resistance:11.2ohms
Base center pitch:16mm 19mm
Pre-wound: with 100 turns hollow shaft
Camera range(Torque):200g-400g
Test Voltage:11.1V
Max Voltage:14.8v
Test Current:0.0099A
Max Current:5A
Test Rotational Speed:1637 rpm
Max Rotational Speed:2180rpm

Storm32 BGC 32Bit 3-Axis Gimbal Controller:

-Hardware:Storm32BGC

-Hardware Version:V1.32

-Firmware:o323bgc-release-v096

Software:

Download the GUl software from here,

https://github.com/oliw42/storm32bgc/blob/master/firmware%20binaries%20%26%20gui/o323bgc-release-v096-

v20160319.zip

How to install:

1. Remove vibration ball,open at the mounting plate.

2.Lock mounting plate with screws at the bottom of the craft.

3.Install the shock absorber ball.

4. Install the camerawith a belt style compact camera.

Note:

Install the camera(be sure to install the camera properly,otherwise it will shake),power on the gimbal and stabilize

it for above 3o seconds,do not shake the gimbal,keepithanging,do not touch the camera with hands,keep it

suspended.After hearing the sound,it can be used normally.

More information please read here,https:/blog.rctoysky.com/?p=831

-M0T0:Connection Pitch(Pitch) Motor
-M0T1:Connection Roll(Roll) Motor
-M0T2:Connection YAW(Direction) Motor
-RC Port:Remont control port.during normal operation,RCO-2 can be accessed by the 3-way PWM singal as a control used when updating the firmware RCO=UAER-RX RC1=UART-TX,SPEKRUM,S-BUS signal is connected RC-O
-RC2 Port:RC20-3 can connect up to four-way Pwm signal as a control use.
-I2C Port:Then the camera's sensor
-I2C Port #2:I2C board on the back of 2# connect external sensors using alternative imu on the motherboard.
-IR Port:Contact infrared light-emitting diode,you can remote control the camera at sony.
-USB Port:0.46 firmare can be used later usb transfer parameters directly connected to the computer.
- Processor: STM32F103RC at 72Mhz
- Motor driver: DRV8313 with short circuit, overheat protection
- Onboard gyro and acceleration sensor MPU6050
- IR LED Interface
- Futaba S-BUS
- Spektrum satellite port
- 7CH PWM/Sum-PPM input/output
- Each axis could connect analog joystick
- With I2C port, could use external 6050 to replace onboard sensor
- 3* AUX port

Specifications:
- Power supply: 9-18V(3-4S)
- Drive current: Max.1.5A
- Dimension: 5-5cm, M3 screw hole, 45mm pitch
- Weight: 10g