B-CUBE.RC - Build Your Drone From here- Build Your Drone From here!

B-CUBE PIXHAWK2.4.8 Flight Control Carbon Fiber 350 Frame Kit Ardupilot Quadcopter BLHELI 30A 2212 Motor ESC Optical Flow

$291.38 USD

Sale Sold out

Type F350 A F350 B F350 NO Battery F350 With Battery

Pixhawk PX4 Autopilot PIX 2.4.8 32 Bit Flight Controller

Features:

Pixhawk 2.4.8 support the latest official ardupilot firmware and PX4 firmware.

1. The advanced 32-bit ARM CortexM4 high-performance processors(2MB flash), can run NuttX RTOS real-time operating system;

2. 14 PWM / servo output;

3. Bus interface (UART, I2C, SPI, CAN);

4. The integrated backup power and backup controller fails, the primary controller fails over to the backup control is safe;

5. Provide automatic and manual modes;

6. Provide redundant power input and failover;

7. Multicolor LED lights;

8. Provide multi-tone buzzer Interface

9. Micro SD recording flight data;

Specifications:

Interface

1.5 high voltage compatible UART 1, 2 with hardware flow control

2. 2 CAN

3.Spektrum DSM / DSM2 / DSM-X satellite receiver compatible input

4.Futaba SBUS compatible inputs and outputs

5.PPM Signal Input

6.RSSI (PWM or voltage) Input

7.I2C

8.SPI

9.3.3 and 6.6VADC input

10. External MICRO USB Interface

M8N GPS:

Power Module：

For PIXHAWK 2.4.8 :used for PIXHAWK2.4.8 AND APM2.8 Flight Control For PIXHAWK PRO :used for PIXHAWK PRO Flight Control For PIXHAWK 6C :used for PIXHAWK 6C Flight Control

Description: This Power Module PRO provides a simple way to supply regulated 5.2V to flight controller from the battery while providing current consumption and battery voltage measurements via analog signal through a 6 Pin JST-GH cable. It comes with pre-soldered wires, capacitor, and XT60 connector on both ends, along with shrink tubing on the PCBA for physical protection. Specification: Input Voltage: 2S-12S PCB Cont. Current Rating: 60A PCB Burst Current Rating: 100A (<60 Sec) Max Current Sensing: 120A Output: DC 5.2V & 3A Max Voltage Divider: 18.182 Amperes per Volt: 36.364 Weight: 20g Please Note: - The XT60 Plug and 12AWG wire that are pre-soldered on the board is rating for 30A continuous current and 60A burst current (< 60 Seconds). If a higher current is being used, the plug type and wire size should be changed accordingly. You can refer to this chart for reference.

BLHELI ESC:

A.Features

A1: Use authentic electronic components to ensure high quality and enhance the current endurance ability of the ESC.

A2: Based on BLHeli firmware, optimized for high performance with great linearity and much quicker throttle response.

A3: Special designed for multirotors, and compatible with fixed-wing aircrafts and helicopters.

A4: Multiple protection features including Low-voltage cut-off protection / over-heat protection / throttle signal loss protection.

A5: Throttle range can be configured and is fully compatible with all receivers, providing smooth, linear and precise throttle response. A6: All parameters can be programmed via using a transmitter, including default settings.

B. Productspecification

2212 920KV Motor

ELRS 2.4G Receiver RX

Product Description:

ExpressLRS aims to provide the best completely open, high refresh radio control link while maintaining a maximum achievable range at that rate with low latency.

SPECIFICATIONS 1

●Brand:B-CUBE

●Model:ELRS 2.4G NANO

●RF Freq:2.4Ghz

●IC:SX1281+ESP8285

●TX Power:100mW

●Color:Black

●Connector:IPEX 1

●Input Power:3.6-5.5V

●Weight:0.4g(receiver only)

●Size:11mm*18mm

●Firmware: BETAFPV Nano 2400 RX 3.3.0

Package Included:

Nano Receiver x 1

T type receiver antenna x 1

Heat shrink tube x 1

30AWG Silicone Wire x 4LiteRadio 3 Radio Transmitter

LiteRadio 3 is a remote control radio transmitter designed primarily for RC models, including multirotor, airplanes. It gives you more than you ever thought possible from an entry-level 8-channel radio.

8 channels in total.

USB Joystick support for most practice simulators.

Nano module bay for external TX module.

Newly designed joystick gimbal for longer usage life.

Support BETAFPV Configurator for updating, configuring, and tuning.

Provide ExpressLRS 2.4G protocol version .

Built-in 2000mAh battery and USB charge supported.