B-CUBE.RC - Build Your Drone From here- Build Your Drone From here!

B-CUBE RemoteID GPS For Pixhawk 2.4.8 Flight Control Ardupilot Quadcopter ArduRemoteID OpenDroneID

$113.69 USD

~~$113.69 USD~~ $113.69 USD

Sale Ausverkauft

Color PX4 RemoteID Package

Anzahl

The product has passed strict CE certification. If you need a PDF or more complete test certificate, please leave a message.

Pixhawk PX4 Autopilot PIX 2.4.8 32 Bit Flight Controller

Features:

Pixhawk 2.4.8 support the latest official ardupilot firmware and PX4 firmware.

1. The advanced 32-bit ARM CortexM4 high-performance processors(2MB flash), can run NuttX RTOS real-time operating system;

2. 14 PWM / servo output;

3. Bus interface (UART, I2C, SPI, CAN);

4. The integrated backup power and backup controller fails, the primary controller fails over to the backup control is safe;

5. Provide automatic and manual modes;

6. Provide redundant power input and failover;

7. Multicolor LED lights;

8. Provide multi-tone buzzer Interface

9. Micro SD recording flight data;

Specifications:

Interface

1.5 high voltage compatible UART 1, 2 with hardware flow control

2. 2 CAN

3.Spektrum DSM / DSM2 / DSM-X satellite receiver compatible input

4.Futaba SBUS compatible inputs and outputs

5.PPM Signal Input

6.RSSI (PWM or voltage) Input

7.I2C

8.SPI

9.3.3 and 6.6VADC input

10. External MICRO USB Interface

PIXHAWK 2.4.8+ 4G TF Card +Safety Button+
Buzzer+M8N GPS+ GPS Holder+ 3DR Power Module

+ Shock Absorber+RemotelD Pix+RemotelD GPS

If the package includes the 3DR Power Module, the current hardware of the 3DR Power Module has been fully upgraded. Previously, it only supported a maximum of 6S, but now it supports a maximum of 12S. By default, XT60 plug is sent. If XT90 plug is required, please leave a message.

RemoteID

RemoteID For PIXHAWK2.4.8: Used for Pixhawk2.4.8 Flight Control

RemoteID For PIXHAWK PRO: Used for Pixhawk PRO Flight Control

RemoteID For PIXHAWK 6C: Used for Pixhawk 6C Flight Control

Send as you select.

How to use RemoteID for ardupilot firmware?

Use for ardupilot, you should compile the code,

git clone --recurse-submodules https://github.com/ArduPilot/ardupilot.git
cd ardupilot
./waf configure --board FMUV3 --enable-opendroneid #FMUV3 is pixhawk2.4.8 and pixhawk PRO board, you can change other
./waf copter

To solve this problem, I have compiled the code, which you can download here,https://www.uavbb.com/firmware/remoteid/

How to use RemoteID for PX4 firmware?

please read here,

https://docs.px4.io/main/en/peripherals/remote_id.html

Overview

RemoteID Module is a low-cost, small-size, and light-weight module that broadcasts information about UAVs in flight through WiFi and Bluetooth. It supports both CAN and serial protocols. It is a FCC and CE-approved radio module.

The products run open-source firmware (ArduRemoteID) and provides a so-called standard Remote ID solution, primarily target drone manufacturers & system integrators.

Note: This product is designed for the Standard Remote ID Solution, primarily targeting drone manufacturers and system integrators, as you need to do your own approval process at the FAA (DoC submission) if you are in the USA. For the most accurate and latest information related to this topic, please refer to the official governance website of your country.

Specification

Radio module:
- Espressif ESP-C3 module
- Bluetooth and WiFi 2.4GHz (ERP): + 20 dBm (100 mW)
- FCC & CE certified radio module
Firmware:
- ArduRemoteID (https://github.com/ArduPilot/ArduRemoteID).
- Supports upgrading firmware via the web interface (“OTA”)
Supported in PX4 & Ardupilot
Protocol: CAN & Serial
Interface:
1x JST GH 4-pin CAN (CAN) port

1x JST GH 6-pin TELEM (UART) port
Antenna Connector type:
On PCB: IPEX Connector
Range: > 5km detection range*
Power: 5V supplied from TELEM or CAN port
LED lights: Bright RGB status LED
Size:
35.3 x 23.5 mm (not including antenna)
Mount: M2 screws
Operating temperature: -40°C to +85°C
Weight:
- PCB only: 4 g
- With Antenna: 16.5g
Certification: FCC& CE

* The detection range depends on many factors such as the receiver antenna gain, transmission protocol, weather conditions, flying height, receiver height line of sight etc. With professional receivers a range of 5 km and more is possible.